ETC
ETC Dual 120V Phase Adept Module for LEDs
- MPN:
- 7050A1296
- Availability:
- Please contact us for additional inventory availability.
- Dimming:
- modules
Description
PhaseAdept modules can be set to two different control modes: Rack mode and Local mode. The control mode is set with a dipswitch that is not accessible when the module is mounted in a dimmer rack (Image 1). Physical covers are in place to help prevent unintended use of the manual controls used in Local Mode.
Rack Mode - When the dipswitch is set towards the rear/backplane side of the module, the module is controlled by the dimmer rack control processor. This mode is supported by Sensor3, and Unison DRd racks. Please ensure that your control processor software is updated to the most recent version before installing PhaseAdept modules.
Local Mode (default) - When the dipswitch is set towards the front/ label side of the module, the module is controlled by an internal dimming engine and manual controls for phase selection (Image 2) and min scale (Image 3). This mode allows PhaseAdept modules to run in any ETC dimmer rack in the field.
- Phase Selection - two dipswitches allow for each output circuit to be either forward or reverse (default) phase. The top and bottom circuit breakers are tied to the left and right dipswitches, respectively. Setting the switch upwards will set the circuit to forward-phase dimming, setting the switch downwards will set the circuit to reverse-phase.
- Min Scale - two dials allow for each output to be set to a different min scale value to provide a dimming curve specific to the requirements of the dimmed load. A legend for using the min scale controls is included on the module label (Image 3)
- Micro USB - there is a micro USB connection (Image 4) next to the min scale controls which supports module firmware updates. Modules do not need to be installed in a dimmer rack in order to be updated
APPLICATIONS
- LED replacement lamps
- Electronic low-voltage transformers
- Electronic LED power supplies requiring forward or reverse phase control
FEATURES
- High-performance dimming of LED loads compatible with any new or installed ETC Sensor or Unison rack
- Two dimmers per module
- High-density modular assembly
- Fully-rated circuit breakers
- Min scale controls
- Forward- or reverse-phase dimming of LED loads
SPECIFICATIONS
- Model: LED10
- MPN: 7050A1296
- Input Voltage: 120V
- Current/Wattage: 10 A / 1.2 kW
- Circuits: 2
- Rack Slots: 1
- Efficiency: 96.23%
- Max BT/ HR|Watts/Channel: 163 BTU / 48W
- Listing: cULus
PHYSICAL
- Modular plug-in assemblies
- Cast aluminum chassis, finished with textured epoxy paint
CIRCUIT BREAKERS
- Fully magnetic to eliminate nuisance tripping
- 10x inrush current rating
- 125%, 10-120 seconds, must-trip rating
- Rated for 100% switching duty applications
ELECTRICAL
- Mains feeds 120V
- 1 W minimum load
- Not suitable for use with magnetic (inductive) loads
- Maximum supported incandescent load - 1000 W (must be set to forward-phase mode before energizing circuit)
POWER DEVICE
- Sealed, patented assembly
- Per-circuit LED indicators
- Integral bonded heatsink
- Integral temperature sensor
FILTERING
- High quality toroidal filters (see module chart for rise times)
LOW VOLTAGE DIMMING
- PhaseAdept modules provide forward- or reverse-phase dimming and are compatible with any ETC dimmer rack
- Phase dimming performance for LED lamps varies considerably depending on the manufacturer and model
PHYSICAL
- Dimensions: 4.9" x 11.8" x 1.5" (127 x 300 x 38 mm)
- Weight: 2.44 lb (1.1 kg)
APPROVALS
- UL and cUL LISTED
- CE Compliant
Related Products
Related Products
ETC Dual 15A Relay Module
ETC
ETC D20 Dual 20A 2.4K Dimmer Module
ETC
ETC D20 Dual 2.4k Dimmer Module, Used
ETC
ETC Dual 20A Relay Module
ETC
ETC D20E Enhanced Dual 20A 2.4K Dimmer Module
ETC